Tight Fit 2008 Contest - PHASE 2 is on page 8

[Oscar]

Have I forgotten to send the email address to anyone here?
-Oscar

i recieved mine, thanks oscar, and uh, can we delete the box after everything is done?

Originally posted by Sobek

Im at 180 Meters and already trough 5 rings, i might even finish the track:P

It's hard, ain't it?
Lol, it took me like 2 hours just to find out where to put the station and lift. Not to mention the countless layout changes.

Originally posted by Oscar

Have I forgotten to send the email address to anyone here?
-Oscar

I'm sending over AIM, right?
Also, can we post our tracks in the exchange after the contest deadline is passed? If not, then when would we be allowed to?

Originally posted by Adrenaguy

i recieved mine, thanks oscar, and uh, can we delete the box after everything is done?

I don't think you should. He probably still needs the beams to check if the coaster/supports is within bounderies.

My track starts with an unusual wave "thingy" to go trough a few rings.

BTW. Can the station be in a ring??

oh yeah good point thanks Ianko. and i would also like to post my track on the exchange when might we be able to do that?

[Oscar]

You are not allowed to delete / remove the box when you are done.
You are not allowed to post it in the exchange until you have been given clearance.
Station can bein a ring.

Wow, this is hard, I just finished my layout this morning, and when I ahg'd it it touched two of the rings that were close calls. grr, back to the old drawing board...

Oscar, will you be checking the bounderies in the sim or the editor?

[Oscar]

ianko66, both the sim and editor.

[hyyyper]

are the rings to be supported or can they hover around?

[Oscar]

The rings can hover around.

i got my layout all done but fails the Estop in the last block, god damb it im gunnhave to redo it

its even propler swarp like with only one inversion

how come when i dowloaded the rings i only have 8 and not 9.

Can the ring be inside the tunnel from the tunneltest if it's under the track?

Edit: Im in, btw.

is there anyway to reload the box...i have the dimensions of 200.13 and 125...one of the vertical supports is 125.28

[Dirk_Ermen]

Originally posted by corn4ahead

is there anyway to reload the box...i have the dimensions of 200.13 and 125...one of the vertical supports is 125.28

Redownload template, insert element? [;)]

[Oscar]

--There's 9 rings, I just checked, you mght have deleted one by accident.

--Ring can be inside the tunnel if it's below the track and doesn't mean the rider getting hurt.

--Set snap to 1 foot rather than using decimals and it will snap into place when you adjust it properly. The box is exactly at 125 with a snap of 1. I will be using a snap of 1 foot to check for stuff.

Ah what the hell, I'm in, first time using the editor in like two years but here we go...

Whoa, throug 6 rings in 400 m!

heh, whoops! over 1800 ft worth of track, heh...

also, can the footers go outside the boundary?

[Oscar]

The footers must be inside the boundaries.

[Dirk_Ermen]

Can we go for the OSRT version of the swarchkopf, please? Those friction wheels look soooo much better on the lift! [;)][:D]

To convince you:

Left, no OSRT. Right, OSRT

[Oscar]

Either wheel assembly type is fine.

[Dirk_Ermen]

Originally posted by Oscar

Either wheel assembly type is fine.

So that means we are allowed to choose the "steel looping coaster (modern)"? [:D] Since you only get those wheels with that tracktype [:)]

[Oscar]

[;)]